Supermodel 3 exiting

[mylkman]

I cannot use my automation/hot key buttons to exit Supermodel 3.  however esc works on the keyboard.  Is this the only way to exit Supermodel3?

I have -res set up like this  - res=1920x1080 -fullscreen and I get errors that say I must set a height and width.  It does finally go into fullscreen but the error is still there.  Even if I remove the -res I still cannot exit using Hotkeys.

Any ideas?

[neil9000]

For closing the emulator copy and paste this into the AHK tab in the manage emulator screen.

; This section closes Supermodel when pressing Escape
$Esc::
{
    Process, Close, {{{StartupEXE}}}
} 

As for the res you should have a , between the height and width not a x.

 

[mylkman]

12 minutes ago, neil9000 said:

For closing the emulator copy and paste this into the AHK tab in the manage emulator screen.

; This section closes Supermodel when pressing Escape
$Esc::
{
    Process, Close, {{{StartupEXE}}}
} 

As for the res you should have a , between the height and width not a x.

 

OK great.  Thank you that cleared up both of my old issues. Now I have a new one.  Since putting in that -res I adand it still got no errors however the game has moved slightly left.  So I put in what you had and it is still moved slightly left.  Any ideas here?

[DOS76]

I set the res in the .ini file I uploaded the file here just look at it with NP++ and set yours accordingly to your preference this .ini is from one of my laptops thus the smaller res.

Supermodel.ini

[mylkman]

6 hours ago, DOS76 said:

I set the res in the .ini file I uploaded the file here just look at it with NP++ and set yours accordingly to your preference this .ini is from one of my laptops thus the smaller res.

Supermodel.ini

But it is just weird that at 1920,1080 still pushes the video screen past the tvs border on the left.  So half the game is unplayable.  Do you think if I set the res inside the config ini it would make a difference?

[DOS76]

I have no clue really its something you will have to test out really. If you are using Windows 10 and it doesn't display right when editing the .ini file try right clicking the Supermodel.exe and go to properties then the compatibility tab try turning off dpi scaling 1st and then full screen optimization if the dpi scaling doesn't do anything. I know both of those setting I've needed to get emulators not displaying correctly to fix issues. Also if you notice in the ini I have full screen and widescreen commands set so maybe they would also help you.

[mylkman]

I will try the widescreen first.  Then I will lay with other settings.  Thank you. 

 

Edit^^^   Looks like just changing widescreen didn't fix the issue.  I went into the properties of the .exe like you said and checking OVERRIDE high DPI scaling behavior scaling performed by and set Application.  Now is there a way to run these games in total fullscreen without the bars all the way around the game? 

Edited December 15, 2017 by mylkman
Edit

[mylkman]

On ‎12‎/‎14‎/‎2017 at 6:35 AM, DOS76 said:

I set the res in the .ini file I uploaded the file here just look at it with NP++ and set yours accordingly to your preference this .ini is from one of my laptops thus the smaller res.

Supermodel.ini

@DOS76  Is your INI file setup using a 360 joystick?

[DOS76]

I'm using a 360 controller but I don't recall having to configure it it just works with Xinput I believe

[mylkman]

3 minutes ago, DOS76 said:

I'm using a 360 controller but I don't recall having to configure it it just works with Xinput I believe

Weird yours is somewhat different than mine.     I ll try to replace mine with yours to see if I like your controls better. 

[DOS76]

Which version of SuperModel are you using? I get the svn builds from EmuCR they are updated quite a bit.