coleroddy Posted March 5, 2020 Share Posted March 5, 2020 (edited) 1 hour ago, Jason Carr said: Yikes, that sounds like a mess. It doesn't sound like I'll be able to fix any of those issues without getting my hands on a G27 set myself. Unfortunately I'll probably have to turn support back off until I can get one. @Jason Carr I don't think you need a G27 for this task. If you can get your hands on any generic DINPUT controller and make it work with the software, I assume G27 will work just fine after it. I'm an average programmer and had made a few things in the past, but nothing on this scope. But I think I'm not far from the truth when I say that you just need a DINPUT device to make it happen. Anyway, I'm avaliable to do any test you need for this. Just gimme a shout. Thanks very much for the fixes. ps.: just to clarify, the issue is just on the remmaping part, but the G27 works on BigBox for everything, even for Automation like "Close Active Window" command combo. I'm using it right now. Edited March 5, 2020 by coleroddy Quote Link to comment Share on other sites More sharing options...
Jason Carr Posted March 5, 2020 Share Posted March 5, 2020 1 hour ago, coleroddy said: @Jason Carr I don't think you need a G27 for this task. If you can get your hands on any generic DINPUT controller and make it work with the software, I assume G27 will work just fine after it. I'm an average programmer and had made a few things in the past, but nothing on this scope. But I think I'm not far from the truth when I say that you just need a DINPUT device to make it happen. Anyway, I'm avaliable to do any test you need for this. Just gimme a shout. Thanks very much for the fixes. ps.: just to clarify, the issue is just on the remmaping part, but the G27 works on BigBox for everything, even for Automation like "Close Active Window" command combo. I'm using it right now. I've tested with numerous DInput devices already, and they do not have those issues, so sadly, yes, I will need the device to get it figured out. Quote Link to comment Share on other sites More sharing options...
coleroddy Posted March 5, 2020 Share Posted March 5, 2020 34 minutes ago, Jason Carr said: I've tested with numerous DInput devices already, and they do not have those issues, so sadly, yes, I will need the device to get it figured out. Oh you did? Bummer. I thought it could be easier. I was wrong. Sorry. Maybe you need a G27 indeed to fix the issue. But as it is now, it's working even if it's not idealy the best solution. I'm gonna keep this beta on a separate installation while we wait for the propper fix. Thanks again, Jason. Quote Link to comment Share on other sites More sharing options...
actiononion Posted March 5, 2020 Share Posted March 5, 2020 14 hours ago, Jason Carr said: Yikes, that sounds like a mess. It doesn't sound like I'll be able to fix any of those issues without getting my hands on a G27 set myself. Unfortunately I'll probably have to turn support back off until I can get one. I just had to combine the pedals using the Logitech software because it was scrolling down. This is a Logitech G920. So happy about this.??? THANK YOU!!! ?????? IMG_6292.MOV Quote Link to comment Share on other sites More sharing options...
jayc001 Posted March 9, 2020 Share Posted March 9, 2020 Hi, Any update on geting the D pad and buttons working on a G920? I've just built a multi driving cab and used the G920 wheel. I was about to buy the premium bigbox but realised I couldn't navigate with the wheel. I really don't want to complicate matters but using vjoy or ahk as a work around. Thanks Quote Link to comment Share on other sites More sharing options...
actiononion Posted March 9, 2020 Share Posted March 9, 2020 13 minutes ago, jayc001 said: Hi, Any update on geting the D pad and buttons working on a G920? I've just built a multi driving cab and used the G920 wheel. I was about to buy the premium bigbox but realised I couldn't navigate with the wheel. I really don't want to complicate matters but using vjoy or ahk as a work around. Thanks Yes it works. If u download the latest beta of launchbox Quote Link to comment Share on other sites More sharing options...
jayc001 Posted March 10, 2020 Share Posted March 10, 2020 Awesome. I'm trying to find where to download the beta though. I can't find any links in the forum or on the main page. Is is restricted to certain users? Quote Link to comment Share on other sites More sharing options...
neil9000 Posted March 10, 2020 Share Posted March 10, 2020 1 minute ago, jayc001 said: Awesome. I'm trying to find where to download the beta though. I can't find any links in the forum or on the main page. Is is restricted to certain users? In Launchbox go to tools/options/updates and turn on beta releases. Quote Link to comment Share on other sites More sharing options...
jayc001 Posted March 10, 2020 Share Posted March 10, 2020 OK so updated to 10.11 beta 12. G920 recognised in controllers. When enabled it constantly scrolls mouse down. I disabled it then cleared all mappings and that stopped the scrolling. When to map buttons and it does not recognise any inputs. I think it still needs work. I'm running w10 IOT LTSC, ver 1809, Logitech driver is 8.85.75.0 and Logitech gaming software 9.02 if that helps. Quote Link to comment Share on other sites More sharing options...
actiononion Posted March 10, 2020 Share Posted March 10, 2020 Tick the combine pedals in the Logitech software. That will stop it scrolling down. If u look for my video a few posts back u can see me using it. Hope that helps Quote Link to comment Share on other sites More sharing options...
jayc001 Posted March 10, 2020 Share Posted March 10, 2020 16 minutes ago, actiononion said: Tick the combine pedals in the Logitech software. That will stop it scrolling down. If u look for my video a few posts back u can see me using it. Hope that helps I tried that and yes it does stop the scrolling but I'm still not able to map buttons. Initially I did get it to recognise button A but it shows as left stick down + button 1 where as button A is actually button 6 under USB game controller. After this happens anyhow the software locks up and won't recognise any input unless I restart it. I've just installed Logitech G Hub and it installs a much newer driver (ver 2019.3.129.0) for the wheel. Interestingly this changed the behaviour. Combining pedals not required to prevent scrolling but when mapping this time button A maps to button 1 but again locks up after this and nothing will unlock till Launchbox is restarted. Quote Link to comment Share on other sites More sharing options...
jayc001 Posted March 11, 2020 Share Posted March 11, 2020 Ok under new beta released same thing however combining pedals now does seem to cure the freezing whilst mapping and I can map all controls. Problem is after spending a couple of weeks getting all games working as I wanted with the G920 I don't want to have to remap all the games to work with combined pedals. Is this something that is likely to be rectified on a later release? Quote Link to comment Share on other sites More sharing options...
Jason Carr Posted March 11, 2020 Share Posted March 11, 2020 7 minutes ago, jayc001 said: Ok under new beta released same thing however combining pedals now does seem to cure the freezing whilst mapping and I can map all controls. Problem is after spending a couple of weeks getting all games working as I wanted with the G920 I don't want to have to remap all the games to work with combined pedals. Is this something that is likely to be rectified on a later release? The problem is that I don't have a G920 to test with currently, so if it does happen, it'll probably be a while. I'm not positive, but I suspect that that issue is specific to that setup. Quote Link to comment Share on other sites More sharing options...
actiononion Posted March 11, 2020 Share Posted March 11, 2020 25 minutes ago, jayc001 said: Ok under new beta released same thing however combining pedals now does seem to cure the freezing whilst mapping and I can map all controls. Problem is after spending a couple of weeks getting all games working as I wanted with the G920 I don't want to have to remap all the games to work with combined pedals. Is this something that is likely to be rectified on a later release? set up a profile using Logitech software so that when bigbox is running the pedals are combined then setup another profile so when the emulators are running the pedals are not combined it works perfectly and my arcade is now complete with bigbox and 72 arcade racers using different emulators Quote Link to comment Share on other sites More sharing options...
jayc001 Posted March 12, 2020 Share Posted March 12, 2020 Thanks I'll give the profile change thing a go. I'm not much of a modern gamer, more retro so haven't really played with the wheel profiles. Quote Link to comment Share on other sites More sharing options...
Sebabav Posted May 2, 2020 Share Posted May 2, 2020 (edited) Hello my friend, after two years of failure i finally find how to use my g27 in menu !!!!!and in games too. 1-First you need to dowload the last version of LB.///telecharger la dernière version de launchbox. Probleme of scrolling down in menu///La vous aller avoir un problème. Le pointeur de la souris va scroller vers le bas....la solution est de combiner les pédales. 2-create a launchbox Logitech profile///Creer un profil logitech pour launchbox 3-aller dans l'onglet edition>paramètres spécifiques du jeu>activer les pédales combinés. Scrolling down is finish!top! but an onother problème now...no gaz and brake in games....//// Donc la ce sera le menu avec la souris et vous pourrez aussi faire défiler le menu avec le volant ! Top ! Mais un autre problème va se passer: le gaz et les freins ne vont plus fonctionner dans les jeux.... Solution in french sorry... La solution: retourner dans le profiler logitech Aller dans dispositif >propriétés >paramètres > décocher la case pédales combinées. Bingo le g27 fonctionne dans le menu et les jeux!!! Enjoy. Edited May 2, 2020 by Sebabav Quote Link to comment Share on other sites More sharing options...
Shawnintexas Posted August 17, 2020 Share Posted August 17, 2020 I’m looking into building a racing MAME for my grandpa because he and I used to love competing against one another when I was a child. He can’t really get out that much and recently mentioned that he loved doing that with me. I wanna surprise him with a game we can play together and want to know how I should get started with the software. I have Launchbox because I build and sell custom arcades so I’m pretty familiar with that already. Any tips or recommendations would be greatly appreciated! thanks! 1 Quote Link to comment Share on other sites More sharing options...
Krakatoa Posted March 5, 2021 Share Posted March 5, 2021 On 3/11/2020 at 3:45 PM, actiononion said: set up a profile using Logitech software so that when bigbox is running the pedals are combined then setup another profile so when the emulators are running the pedals are not combined it works perfectly and my arcade is now complete with bigbox and 72 arcade racers using different emulators Sorry for bumping an old post, Do you know how to set the profiles in G hub? I can't seem to get them to stick. Quote Link to comment Share on other sites More sharing options...
actiononion Posted March 5, 2021 Share Posted March 5, 2021 2 hours ago, Krakatoa said: Sorry for bumping an old post, Do you know how to set the profiles in G hub? I can't seem to get them to stick. Hello mate. Off the top of my head I just created a profile for each emulator, mame, demul, model 2 & 3 then individual profiles for Teknoparrot arcades. Each profile needs linked to each emulators exe so it opens automatically when you launch the game from launchbox Quote Link to comment Share on other sites More sharing options...
actiononion Posted March 5, 2021 Share Posted March 5, 2021 Just checked my pc. I remember now, I couldn’t get on with G-hub and used Logitech gaming software 9.02 instead. Was a lot easier Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.